How to Replace a Tub Yourself: Removing and Replacing.
Automated MarketingListed here below you might get a good deal of helpful resources when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a bathtub isn't precisely brain surgery, yet it does call for solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably difficult project. If the old tub is easily easily accessible, the task can relocate speedily; if you have to open a wall to eliminate the old tub as well as place the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. See to it you have actually certified on your own for the job as well as fit trying it. Instead of employing a service provider to take over a halfway-completed project, it is better to consider employing one before you start. Chances are you might need a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new tub in your restroom if you have already bought a new bathtub and also don't need to change the setup of your previous water pipelines.
Your devices as well as material checklist need to consist of the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, then the first thing you should do is separate the water. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The process of removing the existing faucets can be rather troublesome due to the limited gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth ready for the continuing to be water that will certainly originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. When the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Before going on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, then you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin making certain that the washers remain in place between the faucet and the sink. Secure the faucet in position with the producer given backnut. Once the faucet is firmly in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former type must be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the tub in the needed placement. The wooden boards are useful in evenly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four tiny factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the level as well as readjusting the feet on the bath tub until the spirit level checks out degree.
To set up faucets, fit all-time low of the furthest flexible tap port to the proper supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Switch on the supply of water as well as examine all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill the bath tub as well as additionally examine the overflow electrical outlet and the normal outlet for leaks.
Finally, fix the bath paneling as described in the producer's instruction manual. Tiling as well as sealing around the tub ought to wait up until the tub has been used at least once as this will settle it into its last placement.
Planning for the Installment
To start with, the sustaining structure provided with the bathroom ought to be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is essential to make sure that if the tap features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps unit to stop pressure on the tub.
Fit the versatile tap adapters to the bottom of both taps using 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you use every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath must currently prepare to be fitted in its last position.
Tiling Around the Bath tub
In the location where the bath fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to split a rigid seal, creating the water to pass through the wall in between the bath and also the tiling, causing complications with moisture and possible leakages to the ceiling below.
You can select from a variety of coloured sealers to blend in your components and also fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill up the tub with water prior to sealing, to enable the movement experienced when the tub is in use. The sealant can fracture fairly very early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly offered on the market. It is suggested to fit the tiles making use of waterproof or waterproof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate person who reads about Installing A Bathtub, I imagined sharing that blog post was worth the trouble. Make sure you take the time to promote this entry if you enjoyed reading it. Thank you for taking the time to read it.
Book A Free Estimate